You can’t post conmments that contain an email address. Next up will it be necessary for me to get a new pen in order for the board to work correctly, an Intuos pen? The original pen or any one that works with this UD board is fine — nothing changes here — any of the penabled or ultrapad pen should work like before. Wacom Bamboo Fun 5. Thanks for the reply and again, sorry you lost your friend. Cloudy-grey is actually perfect for doing PCB shots unless it rains! I think, however, your problem might be something to do with the following note from wacom:

Uploader: Dushicage
Date Added: 14 October 2011
File Size: 41.91 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 72871
Price: Free* [*Free Regsitration Required]

Wacom Digitizer Ud-0608-r Vintage Retro Serial Port Computer Device Made Japan

Maybe you could glue or tape the wire on the PCB? One final question, now this probably makes no sense and I do understand we are only pretending to be another device but does the size matter? The hope is that the mapping is ud-00608-r same for the UDR.

July 06,waco, Jul 31, Messages: I did that for the UDR already. Make sure there is no stress on the “pads” of the PCB. I will post some pictures waocm I am done, I think it may be a little more difficult to position the Teensy in this one because the switch is a very small switch I could possibly place it where the current serial out connection is, I can remove that right?


PS Let me know if you see the ROM version there, I had to use a terminal emulator to find out what version ux-0608-r was, sorta like realterm but able to be used wacoj 64bit windows.

Taking a photo of a PCB is really hard. Posted on Apr 03, In the meantime, I’ll keep searching. I looked on google as well as google groups and only found on post. MatthMar 21, A friend had one, and it works fine with XP. I think it will because I get the power, status, and ready lights on the box, the only problem is the box isn’t talking to the computer.

A restart with the tablet connected usually fixes it for me, but I would suggest removing the driver and software and reinstalling them, making sure you have the most up-to-date version- freely available from wacom.

Run the waxbee config tool, flash the teensy. You can opt to leave the Teensy completely outside and attach it with tie-wrap s — or use the unusued Teensy GPIO pins as screw holes just make sure the screws does not make electrical contact with something else.

Wacom Digitizer ii UDR Serial to Windows XP SP3 doesnt – Fixya

Got my Teensy today!!! Try going back a driver version, or so, the last update I tried sorting out my arty friend’s setup wasn’t a good one. Helpful 0 Not Helpful Flag. Tanks to all for your support!


You can attach photos hosted by the forum rather than using an external image hosting site, this means they will stay forever and not disappear after a year or two.

The max point reward for ud-06008-r a question is I tried looking on Wacom’s site but of course this hardware is discontinued. Answer questions, earn points and help others Answer questions.

Wacom Bamboo Fun 5. You can’t post answers that contain an email address. Here is the pinout from the MC I believe it is the same, but I may have missed something. I downloaded drivers for some of the new hardware with the same UD series but when it tries to scan for port 3 the installer just stop and freezes. Wacpm think, however, your problem ud-060-8r be something to do with the following note from wacom: Can’t wait to see what you will come up with.

I want you to build a “table” similar to the wwcom 1″ in the following post. Please assign your manual to a product: One last question are you emulating the intuos when we flash the ROM on these? Use the compatibility mode in Vista to install XP drivers to increase the chances of succeeding.